| INSIDE MOUNT |
- Mark mounting clip locating between 2 to 4
inches from each end of the headrail. Evenly space
intermediate clip locations between end clips at 30
inch intervals. If Available, use mounting template
to determine consistant mounting depth. (See
illustration A) Note: if you do not have a mounting
template, measure depth to allow 1/4" clearance
between louver and window. (i.e. 2" for 3 1/2" louvers)
- If no valance is included, install mounting clips
and skip to number 6. otherwise, continue with
instructions.
- Mark drill holes 3 inches from each end of
the valance and evenly space intermediate drill holes
between the end hgoles at 30 inch iontervals.Note:
Inside surface of the valance has three parallel lines;
align drill holes with center line.
- Hold valance in position and drill through
valance and into ceiling.
- Insert screw through mounting clip and tighten
valance against ceiling into finished mounting
position. (See illustration B)
- Center headrail underneath mounting clips.
- Tilt Headrail and insert into the front ledge of
the mounting clips. Push and roll headrail toward
rear of blind and snap into place.
- To remove, locate rear tab on mounting clip.
(See illustration C)
- While holding rear clip push headrail toward
window and roll back of headrail downward to
release.
|
Illustration A: Mounting Template
 |
Illustration B: Side View
 |
Illustration C: Rear Tab
 |
|
|
| OUTSIDE MOUNT |
- Mount "L" brackets 2 to 4 inches from each end of
headrail. Evenly space intermediate brackets
between end brackets at 30 inch intervals. (See
illustration D)
- Adjust mounting brackets to allow 1/2" clearance
between louver and wall. (i.e. 2 1/4" for 3 1/2"
louvers)
- Center headrail underneath mounting clips.
- Tilt headrail and insert into the front ledge of the
mounting clips. Push and roll headrail toward rear
of blind and snap into place. (See illustration C on
from above)
- If valance is included, "snap" on a valance hanger
next to each "L" bracket. (See illustration E)
- Center valance in relation to the headrail and slide
into valance hanger.
|
Illustration D: Bracket Spacing
 |
Illustration E: Valance Hanger
 |
|
|
| ATTACHING LOUVERS |
- Determine desired light/view direction from
inside the room. (See illustration F)
- Rotate louver hooks so the slot between the long
and the short prong is facing you.
- Push louver into hook until it "snaps" into place.
|
Illustration F: Top Down View
 |
|
|
| REMOVING LOUVERS |
- Gently open louver hook bt inserting a
credit card size piece of rigid plastic between
the vane and the long prong of the louver hook.
(see illustration G)
- Gently remove louver.
|
Illustration G: Louver Hook
 |
|
|
| VALANCE ASSEMBLY |
| SINGLE - TIERED CLOSED SQUARE CORNER |
- Cut fabric insert 1" longer than valance at each end.
- Position fabric and wrap excess around ends.
- Hold fabric into place with closed corner.
- Cut fabric flush with end of return groover.
- Repeat on returns and insert a valance return clip.
NOTE: Cut PVC flush with end of return and secure with
valance return clip. For fabric wrap around back of
return and secure with valance return clip.
Legend for illustration H
- Valance
- Closed Corner
- Valance Return Clip
- Slide fabric into valance leave 1" extra
and roll around to inside as shown.
- Slide fabric into groover and insert valance
return clip to secure fabric.
- Wrap fabric around end of groover.
|
Illustration H: Square Corner Valance Assembly
 |
Illustration I: Assembled Square Corner Valance
 |
| SINGLE - TIERED OPEN SQUARE CORNER |
- Cut fabric long enough to wrap around corner
and cover the entir return plus at least 1 " excess.
- Position open corner and valance returns.
- Position fabric, wrap over open corner and return.
- Trim excess fabric at wall end of valance return.
Legend for illustrations J,K,L
- Fabric
- Valance
- Open Corner
- Slide valance and grrove into opposite sides
of open corner.
- Feed fabric thru valance and corner to
valance return
- Valance return clip
- Slide fabric into groover and insert valance return
clip to secure fabric
- Slide complete unit valance hangers.
|
Illustration J: Open Corner Valance Assembly
 |
Illustration K: Valance Returns and Clips
 |
Illustration L: Assembled Open Corner Valance
 |
| SINGLE - TIERED UNIVERSAL ROUND CORNER |
- Cut fabric long enough to wrap around corner
and cover the entir return plus at least 1 " excess.
- Position open corner and valance returns.
- Position fabric, wrap over open corner and return.
- Trim excess fabric at wall end of valance return.
NOTE: Cut PVC flush with end of return and secure with
valance return clip. For fabric, wrap around back of
return and secure with valance return clip.
Legend for illustrations M,N,O
- Cut valance insert material 8" longer than
the length of the valance and install.
- Install molded valance corner into valance and slide.
- Slide the valance returns onto the valance insert
and rotate the return upward and lock into place.
- Use a (#4) 1/2" screw to secure the valance
return to the valance dust cover.
- Trim excess insert material.
- Valance return clip
|
Illustration M: Rounded Corner Valance Assembly
 |
Illustration N: Securing The Valance Returns
 |
Illustration O: Assembled Rounded Corner Valance
 |
| DOUBLE - TIERED UNIVERSAL ROUND CORNER |
- To install the double tiered universal round corner
follow instructions for the single tiered valance.
- Install valance hangers in back lips of the dust
cover spaced 24" apart plus one for each return.
- For an inside mount, place mounting screws through
clip and locate in rear groove of the dust cover.
Legend for illustration R
- Rear Groove
- Mounting Screw
|
Illustration P: Attaching The Second Tier
 |
Illustration Q: Valance Hangers
 |
Illustration R: Hanging Valance With An Inside Mount
 |
|
|
|
| CORD TENSIONER |
- Establish preferred mounting location. If cord adjustment
is required see instructions below.
- Fully extend tensioning device, rotate post 45 degrees and
lock into extended position.
- Locate mounting position.
- Hold cord taut with cord tensioning device in extended
position and insert screws.
- rotate and release cord tensioning post.
|
Illustration S: Cord Tensioner
 |
Illustration T: Version One: Sill Mount
 |
Illustration U: Version Two: Jamb Mount
 |
Illustration V: Version Three: Wall Mount
 |
|
|
|
| Cord Length |
To reduce the cord length on a side draw
- Place blind in open position.
- Locate cord knot in front of lead carrier.
- Loosen adjusting screw.
- Pull cord to desired length.
- Tie know and then cut excess cord.
- Tighten adjusting screw.
To reduce the cord length on a center draw
- Place blind in closed position.
- Locate cord ends in front of lead carrier.
- Loosen adjusting screw.
- Select cord knot that adjusts cord length only; if Carrier
movement is observed select other cord. Caution - cutting
wrong cord will cause irreparable damage.
- Pull cord to desired length.
- Tie knot and then cut excess cord.
- Tighten adjusting screw.
|
Illustration W: Side Draw
 |
Illustration X: Center Draw
 |
|
|
| Tilt Rod Support Arm |
Tiltrod support arm must be in closed position when
carriers are stacked.
|
Illustration Y: Tilt Rod Support Arm
 |
|
|